Siemens IM 153-4 PN Скачать руководство пользователя страница 233

Страница: 233 / 274

Technical Specifications

10.3 Technical specifications of the IM 153-x

ET 200M
Operating Instructions, 12/2008, EWA-4NEB780600602-08

231

10.3

Technical specifications of the IM 153-x

General technical specifications

In the "S7-300 automation system, module specifications

(

http://support.automation.siemens.com/WW/view/en/8859629

)" reference manual you will

find for the interface module IM 153-x
●

all the general technical data that applies for both the S7-300 and the ET 200M and

●

the deviating technical data and tests for the interface module IM 153-x for expanded

environmental conditions ("outdoor") with the order numbers 6ES7153-1AA8x-0XB0 and

6ES7153-2BA81-0XB0.

Technical specifications of the IM 153 interface modules

The technical specifications for all functions of the various IM 153-x versions are included in

the following table. Check, together with the table "Properties and functions of the variants"

of IM 153-x in chapter "IM 153-x: Variants and properties (Page 17)" to see which version of

your IM 153-x supports these functions.

Technical Specifications

IM 153-1

IM 153-2

IM 153-2 FO

Manufacturer ID

801D

801E

8071

GSD file

SIEM801D.GSD

SIEM801E.GSD

SIEM8071.GSD

•

for DPV1

SI01801D.GSG

SI01801E.GSG

(for IM 153-2AA0x)

SI02801E.GSG

(for IM 153-2BA00)

SI03801E.GSG

(for IM 153-2BAx2)

SI04801E.GSG

(for IM 153-2BAx2)

SI018071.GSG

(for IM 153-2AB0x)

SI028071.GSG

(for IM 153-2BB00)

Dimensions and weight
Dimensions W x H x D (mm)

40 x 125 x 117

Weight, c.

360 g

PROFIBUS DP interface
Baud rates

Up to 12 MBaud

9,6; 19,2; 45,45;

93.75; 187.5;

500 kBaud;

1.5; 12 MBaud

Baud rate detection

yes

Interface

RS 485

FOC

FREEZE capability

yes

SYNC capability

yes

PROFIBUS addresses

1 to 125 permissible

System modification in RUN mode

yes

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды