Siemens IM 153-4 PN Скачать руководство пользователя страница 219

Страница: 219 / 274

Interrupt, error and system messages

9.1 PROFIBUS DP

ET 200M
Operating Instructions, 12/2008, EWA-4NEB780600602-08

217

Interrupts with a different DP master

If the ET 200M is being operated with a different DP master, these interrupts will be shown

as device-related diagnostics of the ET 200M. You must continue to process the respective

diagnostic events in the user program of the DP master.

Saving the Diagnosis

In dependence of byte x+1, transfer the contents of the device-specific diagnosis to a data

block, as
●

The interrupts are updated cyclically.

●

the contents of the diagnosis as of byte x+3 are dependent upon whether S7 diagnosis or

hardware interrupt or removal or insertion interrupt has been reported.

Note
In order to evaluate diagnostics and hardware interrupts via the device-specific diagnosis

with a different DP master you must note:

•

the DP master should be able to save the diagnosis messages, i.e. the diagnosis

messages should be stored within the DP master in a ring buffer. If the DP master

cannot save the diagnosis messages, e.g. then always only the last incoming

diagnosis message will be saved.

•

You must scan the relevant bits in the device-related diagnostic data in your user

program at regular intervals.

•

With an IM 308-C connection as a DP master you cannot use the hardware interrupts

within the device-specific diagnosis, as only incoming - and not outgoing - interrupts

can be reported. E.g. the bit "Upper limit exceeded" is then only reset when the bit

"Lower limit exceeded" is set. End of cycle interrupts are not supported by the IM 308

C as end of cycle interrupts are updated to "1" with each end of cycle (the level of the

signal does not change).

Inserting / removing interrupts with other DP masters

If you use the ET 200M with "Change during Operation" on a different DP master, you must

note that this cannot evaluate the inserting and removing interrupts. You can evaluate the

inserting or removing events in the code- and device-specific diagnosis of the IM 153-x.
Tip: Evaluate the module status in the enhanced diagnosis.

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды