Siemens IM 153-4 PN Скачать руководство пользователя страница 130

Страница: 130 / 274

Maintenance and service

7.11 Saving data and updating the IM 153-4 PN

ET 200M

128

Operating Instructions, 12/2008, EWA-4NEB780600602-08

Insert the SIMATIC Micro Memory Card containing the update in the module slot.

(70

,031

Switch on the power.
–

The IM 153-4 PN automatically detects the SIMATIC Micro Memory Card with the

update files and starts the update.

–

During the update the SF and the BF LEDs light up.

–

After the update is concluded the BF LED flashes at 0.5 Hz.

Switch off the voltage to the IM 153-4 PN and remove the SIMATIC Micro Memory Card

with update.

Re-insert the SIMATIC Micro Memory Card containing the device name into the module

slot and then switch on the supply voltage.

Restart after update

Update via PROFINET IO
In the

STEP 7 user interface, it is possible to set whether

●

the IM 153-4 PN should automatically perform a reset after a successful update in order

to start up using the new firmware.

CAUTION

If the "activate firmware after download" field is checked there is a brief station failure of

the ET 200M. If no precautions have been taken for this case, then the update causes

the CPU (of the IO controller) to go to STOP mode due to a rack failure.

●

The IM 153-4 PN must be reset by switching off the supply voltage. Then, when the

supply voltage is switched on again, the IM 153-4 PN will start up using the new firmware.

Update via SIMATIC Micro Memory Card
If the update was successful, the IM 153-4 PN starts up with the new firmware and is then

ready for operation.

Update unsuccessful

If the update fails, the next time the supply voltage is switched off and on the IM 153-4 PN

starts up with the current ("old") firmware.

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды