PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 97

Страница: 97 / 394

Refitting the driven pulley shaft bearing

- Heat the transmission cover interior using the

heat gun.

N.B.

BE CAREFUL NOT TO OVERHEAT THE COV-
ER AS THIS WOULD DAMAGE THE OUTSIDE
PAINTED SURFACE.

Specific tooling

020151Y

Air heater

- Place the bearing onto the special tool with a little

grease to prevent it from coming out.

- Install the new bearing using the special tool.

N.B.

PROPERLY SUPPORT THE OUTSIDE COVER
TO PREVENT DAMAGING THE PAINTED SUR-
FACE.

Specific tooling

020376Y

Adaptor handle

020358Y

37x40-mm adaptor

020439Y

17 mm guide

Baffle roller

Plastic roller

- Check that the roller does not show signs of wear

and that it turns freely.

- Loosen the retaining bolt using a 13 mm spanner.

- Remove the complete roller with bearing.

N.B.

IF THE ROLLER DOES NOT ROTATE FREELY,
REPLACE THE COMPLETE ROLLER.

Installation of belt anti-vibration roller

- Install the anti-flapping roller with the lip facing the engine crankcase.

- Tighten the central screw to the prescribed torque.

N.B.

TURN THE DRIVEN AND/OR DRIVING PULLEY UNTIL A CORRECT TENSIONING OF THE BELT
IS OBTAINED.

Locking torques (N*m)

MP3 400 i.e.

Engine

ENG - 5

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 97 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: