PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 182 | Manualshive

Страница: 182 / 394

PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 182

THE TRANSMISSION SIDE HALF-CRANKCASE, AS DESCRIBED IN CHAPTER "AUTOMATIC
TRANSMISSION", AND THE HUB COVER WITH THE RELEVANT GEARS AND BEARINGS AS
DESCRIBED IN CHAPTER "FINAL REDUCTION".

Countershaft

- Using a micrometer, measure the 2 bearings of

the countershaft as shown in the figure.

Characteristic

Standard diameter:

17 - 0.01 - 0.02 mm

- Check that the water pump drive is not worn.

Refitting the crankshaft

- Check that the oil pump and countershaft control gear are free from deformations or dents. Replace,

if required.

N.B.

IF YOU HAVE TO REPLACE THE OIL PUMP AND COUNTERSHAFT CONTROL GEAR IT IS NEC-
ESSARY TO REPLACE THE COUNTERSHAFT GEAR AS WELL.

- Before installing the gear on the crankshaft, care-

fully clean the two matching surfaces removing

any residues of LOCTITE from the holes using a

brush.

Blow with compressed air and degrease the mounting holes on both surfaces to make the new LOCTITE

grip.

Apply the recommended product to the holes again.

Recommended products

Loctite 243

Medium strength threadlock

Loctite 243 medium-strength threadlock

- Repeat the same procedure for the 4 fastening screws.

- Insert the control gear on the crankshaft with the hole countersink visible.

- Tighten the 4 fastening screws to the prescribed torque.

N.B.

Engine

MP3 400 i.e.

ENG - 90

«
...
180
181
182
183
184
...
»

Содержание MP3 400 i.e.











































































































































































































































































































































































































Отзывы:

Нет отзывов