PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 132

Страница: 132 / 394

- Align the holes obtained on the flywheel with the

crankcase housing to allow the introduction of the

special tool.

- Tighten the bushing of the flywheel lock tool on

the removing tool threading.

- Insert the special tool as shown in the figure,

making sure that the pins are perfectly inserted in-

to the previously aligned holes and that it is per-

fectly abutted and almost flush with the flywheel.

Specific tooling

020472Y

Flywheel lock wrench

- Loosen the magneto flywheel fastening nut.

- Remove the special tool and the fastening nut.

Engine

MP3 400 i.e.

ENG - 40

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 132 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: