PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 272

Страница: 272 / 394

Hold the crankcase in a perfectly horizontal posi-

tion, heat it with a specific heat gun at a tempera-

ture of about 120 °C, use the specific tool to fit the

bearing of the electric motor. Hit slightly with a

mallet if necessary.

Specific tooling

020363Y

20 mm guide

020151Y

Air heater

020376Y

Adaptor handle

020477Y

Adaptor 37 mm

Before removing the geared motor:

Disable the suspension lock.

- Remove the front shield.

With the set nut indicated in the photograph, re-

move the tensioning cable of the suspension lock-

ing mechanical calliper.

Remove the electrical connection of the geared

motor position potentiometer.

Remove the electrical connection of the geared

motor electric motor.

Suspensions

MP3 400 i.e.

SUSP - 26

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 272 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: