PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 113

Страница: 113 / 394

Removing the wheel axle bearings

- Take out the clip on the outside of the gearbox

cover.

- Support the hub cover using the column kit.

- Pull out the bearing using the special tool.

Specific tooling

020476Y

Stud bolt set

020376Y

Adaptor handle

020477Y

Adaptor 37 mm

020483Y

30 mm guide

- Remove the oil guard using a screwdriver.

Removing the driven pulley shaft bearing

- If you have to remove the driven pulley shaft, the

relevant bearing and the oil guard, remove the

transmission cover and the clutch unit as descri-

bed in the Automatic transmission chapter.

- Extract the driven pulley shaft from its bearing.

- Remove the oil guard using a screwdriver into the

hub gear box.

- Remove the seeger ring shown in the figure.

MP3 400 i.e.

Engine

ENG - 21

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 113 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: