PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 167

Страница: 167 / 394

- Install a new tightener on the cylinder using a new

gasket.

- Tighten the two fastening screws to the prescri-

bed torque.

Locking torques (N*m)

Tightener fastening screws:

11 ÷ 13

- Insert the spring with the central screw and the

washer.

- Tighten the central screw to the prescribed tor-

que.

Locking torques (N*m)

Tightener screw:

5 - 6

- Place the engine with the valve clearance adjustment timing references aligned with the head.

- Check the clearance between valve and rocking lever using a thickness gauge.

PRESCRIBED CLEARANCE

Specification

Desc./Quantity

Inlet

0.15 mm (engine cold)

drainage

0.15 mm (engine cold)

- In case different values are found, adjust by loos-

ening the lock nut and use a screwdriver for the set

screw as shown in the figure.

Refitting the timing chain

The ignition advance is determined electronically on the basis of parameters known by the control unit.

For this reason it is not possible to declare the reference values based on the engine rpm.

The ignition timing value is detectable any time using the diagnostic tester.

It is possible to check whether the ignition advance determined by the system does in fact correspond

with the value actually activated on the engine, by means of the stroboscopic light.

Specific tooling

MP3 400 i.e.

Engine

ENG - 75

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 167 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: