PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 304

Страница: 304 / 394

Brake fluid pipe-calliper fitting

20 ÷ 25

Pad fas-

tening pin

20 ÷ 25

Refitting

- To fit the rear brake calliper, follow the removal steps but in reverse order; be careful to tighten the

screws to the prescribed torque.

Locking torques (N*m)

Screw tightening calliper to the support

20 ÷ 25

Front brake calliper

Removal

- The operations described refer to only one cal-

liper but apply to both.

- Remove the wheel.

- Undo the two fixing screws to the plate and re-

move the calliper.

Overhaul

- Remove the rear brake calliper.

- Suitably hold the brake calliper in a clamp

- Remove the two calliper coupling screws as

shown in the photo

- Remove the two pistons from the calliper body

with the aid of short blasts of compressed air

through the brake fluid holes

- Remove the dust ring and the O-ring of each half

calliper.

- Remove the O-rings in the half calliper.

N.B.

WHEN REMOVING THE O-RINGS, BE CARE-
FUL NOT TO SCRATCH THE HALF CALLIPER
SEATS

Braking system

MP3 400 i.e.

BRAK SYS - 4

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 304 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: