PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 269

Страница: 269 / 394

Place the moulded washer of the flexible trans-

mission control lever shaft and the tongue.

Refit the flexible transmission control lever as

shown in the figure.

Refit the potentiometer (not forcing in the D-type

connector ensures a sole position) with the con-

nector directed to the opposite side of the hydraulic

pump.

Refit the hydraulic pump on the geared motor body

and tighten the screws to the prescribed torque.

Fit but not tighten the pump stem coupling screw

and refit the plastic protection cap.

The synchronisation procedure should be com-

plete when the installation is finished.

Locking torques (N*m)

Geared motor hydraulic pump tightening
screws

11 ÷ 13

Remove the retaining seeger ring of the bearing of

the flexible transmission lever control shaft bear-

ing.

Remove the bearing with the specific tool.

Specific tooling

020376Y

Adaptor handle

020441Y

26 x 28 mm adaptor

020362Y

12 mm guide

MP3 400 i.e.

Suspensions

SUSP - 23

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 269 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: