PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 52

Страница: 52 / 394

Possible Cause

Operation

if they are recessed or if the balls are squashed,

replace them.

Noisy suspension

NOISY SUSPENSION

Possible Cause

Operation

Malfunctions in the suspension system

If the front suspension is noisy, check: the efficien-

cy of the front shock absorbers; the condition of

the ball bearings and relevant lock-nuts, the limit

switch rubber buffers and the movement bushings.

In conclusion, check the tightening torque of the

wheel hub, the brake calliper, the shock absorber
disk in the attachment to the hub and the steering

tube.

Suspension oil leakage

OIL LEAKAGE FROM SUSPENSION

Possible Cause

Operation

Seal fault or breakage

Replace the shock absorber Check the condition

of wear of the steering covers and the adjust-

ments.

Troubleshooting

MP3 400 i.e.

TROUBL - 4

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 52 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: