manualshive.com logo in svg

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 135 / 394

Поделиться
Скачать
PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 135

Inspecting the flywheel components

- Check the integrity of the magnets.

- Check that the magnet support cage is free from

deformation or cracks.

- Check that the flywheel splines exhibit no loos-

ening.

Starter gear rim

- Check that there is no wear or abnormal impres-

sions on the "rollers" of the freewheel and on the

surface of the starter ring gear hub.

- Check the hub outside diameter.

Characteristic

Hub outside diameter:

Diameter 45.665 + 0.008 +0.005 mm

- Check the inside diameter of the bushing of the

starter gearing.

- Check that the toothing is not worn.

Characteristic

Inside diameter of the bushing:

Diameter 27 + 0.020 +0.041 mm

N.B.

IF THE FAULTS DISCOVERED AFFECT THE HUB, REPLACE THE STARTER RING GEAR AND
FREEWHEEL.
IF ONLY THE BUSHING IS WORN, IT IS POSSIBLE TO REPLACE ONLY THE COMPLETE START-
UP RIM. IN THAT CASE, CHECK ALSO THE DIAMETER AND THE SURFACE OF THE CONNEC-
TION ON THE CRANKSHAFT. IN CASE OR IRREGULARITIES, REPLACE THE CRANKSHAFT.

MP3 400 i.e.

Engine

ENG - 43

Содержание MP3 400 i.e.











































































































































































































































































































































































































Отзывы:

Нет отзывов