PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 112

Страница: 112 / 394

Removing the wheel axle

- Remove the countershaft.

- Remove the wheel axis complete with gear.

Removing the hub bearings

- Check all bearings (wear, clearance and noise).

In case of anomalies, proceed as follows.

To remove the gear shaft bearing on the engine

crankcase, use the following parts.

Specific tooling

001467Y014

Pliers to extract ø 15-mm bearings

001467Y034

Extraction pliers for ø 15 mm bear-

ings

001467Y031

Bell

- Use the special extractor to disassemble the

bearing on the engine chassis of the countershaft.

Specific tooling

001467Y006

Pliers to extract 20 mm bearings

001467Y035

Belle for OD 47-mm bearings

- Support the hub cover using the column kit.

- Pull out the bearing using the special tool.

Specific tooling

020476Y

Stud bolt set

001467Y006

Pliers to extract 20 mm bearings

001467Y007

Driver for OD 54 mm bearing

Engine

MP3 400 i.e.

ENG - 20

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 112 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: