PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 297

Страница: 297 / 394

L182.5 ± 0.3 mm

Length of the swinging arm tube on the frame
side:

L 222.5 ± 0.2 mm

- Lubricate roller casings and the plastic bushings

with grease

- Insert the spacers

- Assembly both arms with the appropriate bolt

- Adjust the bolt as shown in the photograph

- Place the swinging arm, frame side, with the pro-

truding part facing the transmission side

Recommended products

AGIP GREASE PV2

Grease for the steering

bearings, pin seats and swinging arm

Soap-based lithium and zinc oxide grease con-

taining NLGI 2; ISO-L-XBCIB2 of the swinging arm

- Check that the silent block is not broken. Other-

wise, replace it.

- Unscrew the retainer to the frame in order to re-

move the silent block supporting clamp.

MP3 400 i.e.

Suspensions

SUSP - 51

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 297 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: