PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 319 | Manualshive

Страница: 319 / 394

PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 319

DO NOT USE OILS OR GREASES WHILE MOUNTING THE COOLING SYSTEM. FAILURE TO OB-
SERVE THIS REGULATION CAN CAUSE IRREVERSIBLE DEFORMATION TO THE SEALING
GASKETS.

Coolant replacement

System top-up rules

- Prepare the mixture of 50% water and coolant.

- Fill the system to reach a level ranging between

the MIX and MAX levels indicated in the expansion

tank filler.

- Do not close the expansion tank with the cap.

- Use a transparent hose to connect the venting

union with the expansion tank filler.

- Loosen the vent and start the engine.

- Keep it open until the air has been fully vented.

- Close the bleed screw.

- Stop the engine.

- Restore the level into the expansion tank and tighten the cap.

- Start the engine and let it warm up to reach the electric ventilation temperature.

- Stop the engine.

- Restore the level with cold engine.

CAUTION

ELECTRIC VENTILATION IS CONTROLLED BY THE TEMPERATURE MEASURED AT THE HEAD.
THE ELECTRIC VENTILATION START DOES NOT MEAN THAT THE VENTING HAS BEEN COM-
PLETED.
VENTING IS COMPLETE WHEN THE EXPANSION TANK TEMPERATURE RISES.

Pompa acqua

Water pump

If noise or loss of liquid at the drain hole of the water pump is discovered, replace the flywheel cover

and the water pump as described in the "Flywheel Cover" Chapter.

Proceed to carry out a few preliminary operations as described below:

MP3 400 i.e.

Cooling system

COOL SYS - 5

«
...
317
318
319
320
321
...
»

Содержание MP3 400 i.e.











































































































































































































































































































































































































Отзывы:

Нет отзывов