PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 115

Страница: 115 / 394

= diameter 30 - 0.010 -0.023 mm

= diameter 15 - 0.01 -0.02 mm

Connection diameter for shaft driven pulley:

= diameter 17 - 0.01 -0.02 mm

= diameter 20 - 0.01 -0.02 mm

= diameter 25 - 0.01 -0.02 mm

Inspecting the hub cover

- Check that the mounting surface is not damaged or deformed.

- Check the bearing bearings.

In case of faults, replace the hub cover.

Refitting the driven pulley shaft bearing

- Heat the crankcase using the heat gun.

Specific tooling

020151Y

Air heater

- Insert the driven pulley shaft bearing until it abuts

against the bottom of the seat using the special

tool.

N.B.

PLACE IT WITH THE BALLS FACING THE HUB
(THIS APPLIES TO BEARINGS WITH PLASTIC
CAGE).

Specific tooling

020376Y

Adaptor handle

020360Y

Adaptor 52 x 55 mm

020364Y

25-mm guide

MP3 400 i.e.

Engine

ENG - 23

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 115 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: