PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 124

Страница: 124 / 394

Refitting the stator

- Install the stator assembly together with the wir-

ing harness, tightening the 3 screws to the pre-

scribed torque.

N.B.

INSERT THE RUBBER WIRING SEALING GAS-
KET INTO THE SPECIAL SEAT ON THE
CRANKCASE.

Locking torques (N*m)

Stator retainers

8 - 10

- Install the wiring guide bracket tightening the 2

screws to the prescribed torque.

Locking torques (N*m)

Stator cable harness guide bracket screws

3 -

Refitting the flywheel cover components

- Before reassembling, check that all components

are perfectly clean.

- For the cover, carefully check all lubrication chan-

nels, in particular:

- The 3 by-pass channels.

- Oil pressure sensor feeding duct.

Engine

MP3 400 i.e.

ENG - 32

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 124 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: