manualshive.com logo in svg

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 215 / 394

Поделиться
Скачать
PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 215

After switching to «

ON

», check that there is battery

voltage, for about 2 seconds, between the Black-

Green cable of the pump connector and the

ground lead with the pump connector disconnec-

ted. Otherwise, check the continuity of the Black-

Green cable between the pump connector and the

remote control base.

Check the efficiency of the earth line of the fuel

pump by measuring the continuity between the

pump connector black cable, system side, and the

earth.

If, when switching to «

ON

», the pump continues to

turn after 2 seconds of activation, check, with the

control unit disconnected and the injection load re-

mote control disconnected, that the Black-Purple

cable (pin 20 on the interface wiring) is insulated

from the ground.

Specific tooling

020331Y

 

Digital multimeter

Circuit leak test

Install the specific tool for checking the fuel pressure, with the pipe fitted with the gauge.

MP3 400 i.e.

Injection

INJEC - 19

Содержание MP3 400 i.e.











































































































































































































































































































































































































Отзывы:

Нет отзывов