PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 220

Страница: 220 / 394

Check the power supply line of the injection load

remote control energising coil: after switching to

"ON", make sure there is battery voltage, for two

seconds, between the Red-White cable and Black-

Violet cable of the remote control base. If there is

not, check the continuity of the Red-White cable

between the fuse box and the remote control base

and of the Black-Purple cable between the pin 20

of the control unit and the remote control base.

N.B.

CONTINUITY TESTS MUST BE CARRIED OUT
WITH THE COMPONENTS DISCONNECTED.
(REMOTE CONTROLS, CONTROL UNIT,
FUSES ETC.).

Injection

MP3 400 i.e.

INJEC - 24

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 220 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: