manualshive.com logo in svg

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 190 / 394

Поделиться
Скачать
PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 190

approx. 1.5 bar

YES go to 7 NO go to 8

7

 - Replace the oil minimum pressure switch.

8

 - If pressure lower than 1.3 - 1.5 bar is measured.

AHEAD go to 9

9

 - Replace the oil filter and repeat the pressure check with oil at 80°C.

YES go to 10 NO go to 13

10

 - The failure was fixed.

It is recommended to respect the suggested number of kilometres covered.

11

 - Check and restore the electrical system.

12

 - If pressure lower than 4 bar is measured.

AHEAD go to 9

13

 - Remove the flywheel cover and check the by-pass and the cover sealing gasket efficiency towards

the case internal side, as described in the "Flywheel cover" chapter.

YES go to 14 NO go to 15

14

 - Check whether there is an irregular clearance on the crankshaft:

- axial clearance (see the "Crankcase and crankshaft" chapter)

- radial clearance, especially in the direction of the cylinder axis

- clearance according to the direction of rotation with the connecting rod in quadrature

YES go to 16 NO go to 17

15

 - Replace the faulty components ("Flywheel cover" chapter).

16

 - Overhaul the engine ("Crankcase and crankshaft" chapter).

17

 - Open the engine crankcase and remove the oil pump, as described in the "Crankcase and crank-

shaft" chapter.

- Check the oil pump as described in the following pages.

- Check that the cooling nozzle and the timing feeding jet are properly installed.

- Visually inspect the crankshaft couplings and their size ("Crankcase and crankshaft" chapter).

N.B.

POTENTIAL IRREGULARITIES IN COUPLINGS AND THE TIMING SYSTEM COMPONENTS CAN-
NOT BE DETECTED WHEN INSPECTING THE LUBRICATION PRESSURE. THEY MAY BECOME
EVIDENT BY AN INCREASE IN NOISE.

N.B.

IN CASE OF IRREGULAR PRESSURE ON THE CRANKCASE, CARRY OUT A VISUAL AND DI-
MENSIONAL INSPECTION OF THE TIMING SYSTEM COMPONENTS (SEE "THERMAL GROUP
AND TIMING SYSTEM" CHAPTER).

Oil pressure check

1

 - In case of oil leaks from the oil filter or from the flywheel cover coupling gasket, check the lubrication

pressure.

AHEAD go to 2

Engine

MP3 400 i.e.

ENG - 98

Содержание MP3 400 i.e.











































































































































































































































































































































































































Отзывы:

Нет отзывов