PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 158 | Manualshive

Страница: 158 / 394

PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 158

TO AVOID SCORING THE CONTACT SURFACE, DO NOT KEEP ROTATING THE VALVE WHEN
NO LAPPING COMPOUND IS LEFT. CAREFULLY WASH THE CYLINDER HEAD AND THE
VALVES WITH A SUITABLE PRODUCT FOR THE TYPE OF LAPPING COMPOUND BEING USED.

CAUTION

DO NOT REVERSE THE FITTING POSITIONS OF THE VALVES (RIGHT - LEFT).

Inspecting the springs and half-cones

- Check that the upper and lower supporting spring

washers, the cotters and the oil seal show exhibit

no signs of abnormal wear. Replace a component

when worn.

- Measure the unloaded spring length.

Characteristic

Standard length:

44.4 mm

Admissible limit after use:

42.4 mm

Refitting the valves

- Place the valve spring support washers on the

head.

- Alternately insert the 4 oil guards using the spe-

cial tool.

- Lubricate the oil guards and the valve guides.

Specific tooling

020306Y

Punch for assembling valve seal

rings

Engine

MP3 400 i.e.

ENG - 66

«
...
156
157
158
159
160
...
»

Содержание MP3 400 i.e.











































































































































































































































































































































































































Отзывы:

Нет отзывов