PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 166

Страница: 166 / 394

- Turn the engine to move the references to the top

as shown in the figure (intake end).

- Insert the valve lifting device mass stop bell.

- Tighten the retaining screw to the prescribed torque, using the recommended product.

N.B.

THE BELL TIMING IS ENSURED BY THE COUNTERWEIGHT MASS FASTENING SCREW HEAD.

Recommended products

Loctite 243

Medium strength threadlock

Loctite 243 medium-strength threadlock

- Check that the decompression mass is free and

that it is pulled by the spring.

Locking torques (N*m)

Valve lifter mass stop bell fixing screws:

30 -

- Place the tightener cursor in the rest position,

keeping the retain tab pressed.

Engine

MP3 400 i.e.

ENG - 74

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 166 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: