PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 149

Страница: 149 / 394

- Using a bore meter, measure the cylinder inner

diameter at a given height according to the direc-

tions shown in the figure.

Characteristic

43 mm

Standard diameter:

85.8 mm nominal value

- Check that coating is free from flakes.

- Check that the head matching surface exhibits no deformations or wear.

Characteristic

Maximum allowable run-out:

0.05 mm

- Pistons and cylinders are classified into categories based on their diameter. The coupling is carried

out in pairs (A-A, B-B, C-C, D-D).

N.B.

REFER TO THE «SPECIFICATIONS» SECTION FOR THE SIZES OF THE CYLINDER AND THE
CYLINDER-PISTON COUPLING CLEARANCES.

Inspecting the piston rings

- Alternately insert the three sealing rings into the

cylinder, in the area where it retains its original di-

ameter. Using the piston, insert the rings perpen-

dicularly to the cylinder axis.

- Make sure that each single sealing ring evenly

adheres to the cylinder liner. If it does not, this

means the ring is worn. Replace it.

- Measure the opening (see figure) of the sealing

rings using a feeler gauge.

MP3 400 i.e.

Engine

ENG - 57

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 149 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: