PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 101

Страница: 101 / 394

- Using the special tool inserted through the roller

bearing, pull out the ball bearing.

N.B.

PROPERLY SUPPORT THE PULLEY TO PRE-
VENT DAMAGING THE THREADING.

Specific tooling

020376Y

Adaptor handle

020456Y

Ø 24 mm adaptor

020363Y

20 mm guide

N.B.

IF YOU NEED TO OVERHAUL THE BEARINGS ON AN ASSEMBLED DRIVEN PULLEY UNIT, IT IS
NECESSARY TO SUPPORT THE UNIT BY THE BELL

Specific tooling

001467Y002

Driver for OD 73 mm bearing

- Remove the roller bearing using the special tool,

supporting the fixed half-pulley with the bell.

Specific tooling

020376Y

Adaptor handle

020375Y

Adaptor 28 x 30 mm

020364Y

25-mm guide

001467Y002

Driver for OD 73 mm bearing

Inspecting the driven fixed half-pulley

- Check that the belt contact surface is free from

wear.

- Measure the outer diameter of the pulley bushing.

Characteristic

Minimum admissible diameter

49.96 mm

Standard diameter:

49.965 mm

MP3 400 i.e.

Engine

ENG - 9

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 101 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: