manualshive.com logo in svg

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 73 / 394

Поделиться
Скачать
PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 73

Characteristic

MASTER key:

RED KEY

SERVICE key.

BLACK KEY

Diagnostic codes

The immobiliser system is tested each time the ig-

nition-key switch is turned from OFF to ON. During

this diagnosis phase a number of control unit sta-

tuses can be seen and various light codes dis-

played. Regardless of the code transmitted, if at

the end of the diagnosis the led remains off per-

manently, the ignition is enabled. If, however, the

led remains on permanently, it means the ignition

is inhibited:

1. Previously unused control unit - key inser-

ted

: a single 2 second flash is displayed, after

which the LED remains off permanently. The keys

can be stored to memory, the vehicle can be star-

ted but with a limitation imposed on the number of

revs.

2. Previously unused control unit - transpond-

er absent or cannot be used

: The LED is per-

manently ON; in this condition, no operations are

possible, including starting of the vehicle.

3

. 

Programmed control unit - the service key in

(normal condition of use)

: a single 0.7 second

flash is displayed, after which the LED remains off

permanently. The engine can be started.

4

. 

Programmed control unit - Master key in

: a

0.7 sec. flash is displayed followed by the LED re-

maining off for 2 sec. and then by short 0.46 sec.

flashes the same number of times as there are

keys stored in the memory including the Master

key. When the diagnosis has been completed, the

MP3 400 i.e.

Electrical system

ELE SYS - 21

Содержание MP3 400 i.e.











































































































































































































































































































































































































Отзывы:

Нет отзывов