PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 180

Страница: 180 / 394

- The oil feeding channel section is also affected by the bushings driving depth compared with the

crankshaft axial clearance of the limiting surface.

N.B.

TO KEEP THE BUSHINGS ON THE CRANKCASE IN SUCH POSITION, DRIVING IS FORCED ON
CAST-IRON RINGS INSERTED IN THE CASTING OF BOTH CRANKCASE HALVES.

- Check the inside diameter of the main bushings

in the three directions indicated in the diagram.

- Repeat the measurements for the other bushing

half. see diagram.

N.B.

DO NOT TAKE THE MEASUREMENT ON THE
TWO HALF-SHELL COUPLING SURFACE
SINCE THE ENDS ARE RELIEVED TO ALLOW
BENDING DURING THE DRIVING OPERATION.

Before assembling, check that the clearance between the engine crankcase bushing and the crankshaft

is within the predetermined limits.

Characteristic

Crankshaft-bushing maximum clearance admitted:

0.08 mm

- The standard bushing diameter after driving is variable on the basis of a coupling selection.

- The crankcase bushing seats are classified into 3 categories while the crankshaft ones, into 2 cate-

gories.

- Bushings are subdivided into 4 categories according to their thickness (see the table).

CHECK THE BENCH BUSH

Name

Description

Dimensions

Initials

Quantity

Type A - Red

1.971 ÷ 1.974

Type B - Blue

1.974 ÷ 1.977

Type C - Yellow

1.977 ÷ 1.980

Type D - Green

1.980 ÷ 1.983

Coupling chart

The following kinds of bushings indicated in the table must be used according to the kind of coupling

between the crankshaft and the crankcase.

Engine

MP3 400 i.e.

ENG - 88

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 180 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: