PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 85

Страница: 85 / 394

. Potentiometer ground lead, rpm sensor, rider

presence sensor (Yellow)

. Ground (Black)

. Live supply (Yellow-Red)

. CAN "H" Line (Pink-White)

. Left wheel turning sensor (Green)

. Right wheel turning sensor (Red)

. Potentiometer signal (Green-Blue)

. Locking/unlocking switch (Green-Grey)

. Horn remote control for alarms (White)

. Geared motor (White-Red)

. Battery powered (Blue-Red)

. Diagnosis (Purple-White)

. Locking/unlocking switch (Yellow-Blue)

. Calliper sensor (Brown)

. Locking/unlocking switch (Purple-Black)

. Rider presence sensor (Purple)

. Scooter speed signal (Sky blue)

. Geared motor (Blue)

Remote seat opening

Zeroing

- Remove the left side fairing to access the saddle

opening receiver control unit indicated in the pho-

tograph

- Remove the metal terminal and connect it to a

good earth point, or to terminal 7 (black), for at

least 10 seconds.

- In this operation all the remote controls stored in

the control unit will be deleted.

WARNING

THE CONTROL UNIT CAN PROGRAMME UP
TO 8 REMOTE CONTROLS.

MP3 400 i.e.

Electrical system

ELE SYS - 33

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 85 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: