PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 189

Страница: 189 / 394

YES - go to 3 NO go to 11

Check the actual oil pressure.

AHEAD - go to 4

- Remove the switch and fit the special tool with the relevant gasket.

Specific tooling

020193Y

Oil pressure gauge

020434Y

Oil pressure control fitting

- Remove the dipstick with the oil filling cap and insert a cap fitted with the temperature probe supplied

with the special tool. Insert the probe to feel contact with the crankcase bottom and pull back a few

millimetres.

Specific tooling

020331Y

Digital multimeter

AHEAD - go to 5

- Measure the pressure with cold and idling engine.

STANDARD VALUES

Specification

Desc./Quantity

20°C Temperature

1400 rpm

approx. 4.5 bar

N.B.

RPM CAN BE MEASURED BOTH BY THE EXHAUST GAS ANALYSER AND BY THE DIAGNOSTIC
TESTER

Specific tooling

020460Y

Scooter diagnosis and tester

YES go to 6 NO go to 12

- Let the engine warm up and repeat the check with hot oil.

STANDARD VALUES

Specification

Desc./Quantity

80°C Temperature

1400 rpm

MP3 400 i.e.

Engine

ENG - 97

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 189 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: