PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 140

Страница: 140 / 394

- Install the chain guide retain plate tightening the

3 screws to the prescribed torque.

N.B.

BEFORE TIGHTENING THE SCREWS, MOVE
THE START-UP RIM IN CONTACT WITH THE
CRANKCASE AND CHECK THAT IT IS FREE
TO ROTATE IN ANTICLOCKWISE DIRECTION.

Locking torques (N*m)

Chain guide sliding block retain plate fasten-
ing screws

3 ÷ 4

Refitting the starter motor

- Check that the O-ring is in good working order

and lubricate it.

- Insert the starter motor.

- Tighten the 2 fastening screws to the prescribed

torque.

Locking torques (N*m)

Starter motor screws

11 ÷ 13

Cylinder assy. and timing system

- Remove the external and internal transmission

cover.

- Remove the flywheel cover, the flywheel and the

torque limiter.

Engine

MP3 400 i.e.

ENG - 48

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 140 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: