PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 150

Страница: 150 / 394

- If higher values than those prescribed are meas-

ured, replace the linings.

Check the size of the sealing ring opening:

Compression ring:

0.15 ÷ 0.35 mm. Max. value 0.5 mm

Oil scraper ring:

0.25 ÷ 0.50 mm. Max. value 0.65 mm

Oil scraper ring:

0.25 ÷ 0.50 mm. Max. value 0.65 mm

Rings/housing coupling clearances:

Carefully clean the sealing ring housings.

Place a thickness gauge between the ring and the

housing as shown in the drawing and check the

coupling clearances.

Top ring Standard coupling clearance:

0.01÷0.06 mm

Maximum clearances allowed after use:

0.10

Intermediate ring

Standard coupling clear-

ance:

0.02÷0.07 mm

Maximum clearances allowed after use:

0.10

Oil scraper ring

Standard coupling clearance:

0.01÷0.06 mm

Maximum clearances allowed after use:

0.10

Replace the piston if clearances exceed the max-

imum limits specified in the table.

Removing the piston

- Install piston and wrist pin onto the connecting

rod, aligning the piston arrow the arrow facing to-

wards the exhaust.

Engine

MP3 400 i.e.

ENG - 58

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 150 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: