PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 185

Страница: 185 / 394

- Insert the 14 fastening screws by arranging the

single shorter screw "

" and the single longer

screw "

" as shown in the figure.

- Tighten the screws thoroughly and tighten to the prescribed torque.

- Check that the crankshaft rotates freely.

N.B.

REMOVE ANY EXCESS FROM THE CRANKCASE COUPLING GASKET ON THE CYLINDER
PLANE, TO ENSURE BETTER SEALING PERFORMANCE.

Locking torques (N*m)

Engine-crankcase coupling screws

11 ÷ 13

- Install the thermal unit (cylinder, head, piston) as described in section "Thermal unit and timing sys-

tem".

- Install the flywheel with start-up control as described in the "Flywheel and start-up" chapter.

- Install the flywheel cover with the cooling system sleeves, as described in the "Flywheel cover chapter".

- Install the complete driving pulley, the transmission cover and the relevant mesh filter and the outside

transmission cover as described in the section "Automatic transmission".

See also

Cylinder assy. and timing system
Flywheel cover

Lubrication

TECHNICAL SPECIFICATIONS

SUMP CAPACITY

Specification

Desc./Quantity

Overhaul

1.7 l

Oil and filter replacement

1.5 l

RECOMMENDED ENGINE OIL

Product

Description

Specifications

AGIP CITY HI TEC 4T

Engine oil

SAE 5W-40, API SL, ACEA A3,

JASO MA Synthetic oil

OIL PUMP

Specification

Desc./Quantity

Type

Trochoidal

Rotor thickness

8 mm

Assembly clearances

Lobe ends 0.05-0.008 mm

Outside rotor radial clearance

0.05- 0.12 mm

Rotor axial clearance

0.025 - 0.065 mm

BY-PASS

Specification

Desc./Quantity

Type

with piston

MP3 400 i.e.

Engine

ENG - 93

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 185 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: