PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 199

Страница: 199 / 394

- Lambda probe strength

The system implements an idle feeding correction with cold engine through a Stepper motor on a by-

pass circuit of the throttle valve. The control unit manages the Stepper motor and the injector opening

time, thereby ensuring the idle steadiness and the proper combustion.

In all conditions of use, mixture preparation is managed by modifying the injector opening time.

The fuel supply pressure is kept constant based on the ambient pressure.

The

fuel supply circuit

consists of:

- Fuel pump

- Fuel filter

- Injector

- Pressure regulator

The pump, the filter and the regulator are placed inside the fuel tank on a single support.

The injector is connected by a pipe with fast-release fittings. The pressure regulator is located at the

beginning of the circuit.

The fuel pump is controlled by the MIU control unit ; this ensures the scooter safety

The

ignition circuit

consists of:

- HV coil

- HV cable

- Shielded cap

- MIU control unit

- Spark plug

The MIU control unit manages ignition with the best advance ensuring four-stroke timing (ignition only

in the compression phase) at the same time.

The MIU injection-ignition system controls engine functions by means of a pre-set program.

Should any input signals fail, an acceptable working order of the engine is ensured to allow the user to

reach a service station.

Of course, this cannot happen when the rev counter signal is missing, or when the failure involves the

control circuits:

- Fuel pump

- HV coil

- Injector

MP3 400 i.e.

Injection

INJEC - 3

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 199 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: