PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 223

Страница: 223 / 394

Install the appropriate tool for the fuel pressure

check and position the manifold over a container

graduated by at least 100 cc. Connect the injector

with the cable making up part of the supply for the

injection tester. Connect the clamps of the cable

to an auxiliary battery. Activate the fuel pump with

the active diagnosis. Check that within 15 approx.

70 cm³ of fuel is delivered with adjustment pres-

sure of approx. 3 BAR.

Specific tooling

020480Y

Petrol pressure check set

Proceed with the injector seal test.

Dry the injector outlet with a blast of compressed

air. Activate the fuel pump. Wait for one minute,

making sure there are no leaks coming from the

injector. Slight oozing is normal.

Value limit = 1 drop per minute

Immobiliser circuit

The electronic ignition system is controlled by the

control unit with the integrated Immobilizer sys-

tem. The immobilizer is an antitheft system that

allows the vehicle to be operated only when it is

started with coded keys recognised by the control

unit. The code is integrated in a transponder in the

key block. This allows the driver clear operation

without having to do anything other than just turn-

ing the key. The Immobiliser system consists of the

following components:

- electronic control unit

MP3 400 i.e.

Injection

INJEC - 27

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 223 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: