PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 168

Страница: 168 / 394

020460Y

Scooter diagnosis and tester

020330Y

Stroboscopic light for timing control

Proceed as follows:

- Remove the outside transmission cover as de-

scribed in the automatic transmission chapter.

- Remove the TDC reference inspection cap be-

tween flywheel and crankcase cover. See the fly-

wheel cover chapter.

- By the driving pulley, turn the engine to find the

alignment of the references to identify the TDC.

- Repeat for the reference between driving pulley

and transmission housing.

Engine

MP3 400 i.e.

ENG - 76

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 168 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: