PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 181

Страница: 181 / 394

KEY

= Crankshaft category

= Crankcase half-shell category

= Red

= Blue

= Yellow

= Green

In case of breakdown, crankcases are together with bushings and are classified according to the centre

to centre distance of the countershaft. Find below the possible couplings.

- Complete FC1 type crankcase equipped with bushings for housing a category 1 crankshaft and a

countershaft with centre to centre distance A.

- Complete FC2 type crankcase equipped with bushings for housing a category 2 crankshaft and a

countershaft with centre to centre distance A.

- Complete FC3 type crankcase equipped with bushings for housing a category 1 crankshaft and a

countershaft with centre to centre distance B.

- Complete FC4 type crankcase equipped with bushings for housing a category 2 crankshaft and a

countershaft with centre to centre distance B.

N.B.

THE CRANKSHAFT CATEGORY IS STAMPED ON THE COUNTERWEIGHT SHOULDER.

A spare crankcase cannot be combined with a driving shaft with mixed categories. Spare shafts have

half-shafts of the same category.

N.B.

TO REPLACE THE HALF-SHAFTS, REMOVE THE COUNTERSHAFT BEARINGS AS DESCRIBED
ABOVE. REMOVE THE COMPLETE DRIVEN PULLEY AND THE ANTI-FLAPPING ROLLER FROM

MP3 400 i.e.

Engine

ENG - 89

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 181 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: