PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 148

Страница: 148 / 394

- Calculate the coupling clearance between pin

and connecting rod end.

Characteristic

Standard clearance:

0.015 ÷ 0.029 mm

Inspecting the piston

- Measure the capacity diameter on the piston.

Characteristic

Standard diameter:

22 + 0.006 + 0.001 mm

- Calculate the piston pin coupling clearance.

N.B.

THE PIN HOUSINGS HAVE 2 LUBRICATION CHANNELS. FOR THIS REASON, MEASUREMENT
MUST BE MADE ACCORDING TO THE PISTON AXIS.

Characteristic

Standard clearance:

0.001 ÷ 0.010 mm

- Measure the outside diameter of the piston, per-

pendicular to the gudgeon pin axis.

- Take the measurement in the position shown in

the figure.

N.B.

REFER TO THE «SPECIFICATIONS» SECTION
FOR THE SIZES OF THE PISTON AND THE
CYLINDER-PISTON COUPLING CLEARAN-
CES.

Characteristic

10 mm

Piston diameter:

85.8 mm nominal value

Engine

MP3 400 i.e.

ENG - 56

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 148 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: