PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 89

Страница: 89 / 394

CAUTION

THIS OPERATION MUST BE CARRIED OUT WHEN THE ENGINE IS COLD.

- Remove the rear wheel.

- Remove the bracket supporting the rear brake

callipers and the callipers as well.

- After removing the air filter from the crankcase,

undo the screws fixing the bracket that secures the

rear brake pipes.

- Remove the pipe feeding coolant into the pump

as shown in the photograph and then empty the

system.

- Remove the engine coolant outlet pipe as indi-

cated.

- Disconnect the fuel delivery pipe from the injector

by removing the screw locking the retainer clamp.

- Disconnect the injector wiring and the throttle

body control unit wiring.

- Remove the coolant outlet pipe from the motor

as indicated.

MP3 400 i.e.

Engine from vehicle

ENG VE - 3

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 89 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: