PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 39

Страница: 39 / 394

- Bring the reference mark onto the transmission

side between the fan and the transmission cover

as shown in the photograph.

- Refit the spark plug.

- Refit the plastic cap on the flywheel cover.

- Adjust the spark gap to the contact position (no

reference mark visible) and install it on engine be-

tween the spark plug and spark plug cap

- Connect the induction calliper on the spark gap

cable respecting the proper polarity (the arrow on

the calliper must be pointing at the spark plug).

- Connect the diagnostic tester.

- Start the engine.

- Select the menu on the "parameter" function.

- Select the stroboscopic light command in the tra-

ditional four-stroke engine position (1 spark 2

revs).

- Check that the real values of rpm and ignition

advance match those measured using the diag-

nostic tester.

If the values do not correspond, check:

- distribution timing

- revolution-timing sensor

- Injection control unit

Specific tooling

020460Y

Scooter diagnosis and tester

020330Y

Stroboscopic light for timing control

020621Y

HV cable extraction adaptor

MP3 400 i.e.

Maintenance

MAIN - 5

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 39 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: