PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 91

Страница: 91 / 394

Remove the lower screw of the left-hand shock

absorber.

- Remove the engine-swinging arm fixing pin by

undoing the nut and operating on the head of the

pin as shown in the photograph.

- The engine is now free.

When refitting the engine onto the scooter, carry out the removal operations but in reverse order and

respect the tightening torques shown in the Specifications Chapter.

-Check the engine oil level and if necessary top it up with the recommended type.

- Fill and bleed the cooling circuit.

- Check the functioning of the accelerator and the electrical devices.

CAUTION

PAY PARTICULAR ATTENTION TO POSITIONING THE THROTTLE COMMAND TRANSMISSION
PROPERLY.

MP3 400 i.e.

Engine from vehicle

ENG VE - 5

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 91 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: