manualshive.com logo in svg

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 312 / 394

Поделиться
Скачать
PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 312

Front

- The operations described refer to only one cal-

liper but are valid and must be observed for both.

- Remove the rubber hood from the bleed screw.

- Insert a rubber pipe in the bleed screw to permit

the brake fluid to be recovered.

- With the right-hand brake lever, load the system and bring it up to the required pressure.

- Keeping the right-hand brake lever pulled, loosen the bleed screw to permit the air in the system to

escape. Then tighten the bleed screw.

- Repeat the operation until only brake fluid comes out of the rubber pipe.

- Remove the fluid recovery pipe and refit the rubber hood over the bleed screw.

- Top up the brake fluid to the right level in the tank.

N.B.

DURING THE BLEEDING OPERATIONS, MAKE SURE THE BRAKE FLUID DOES NOT COME INTO
CONTACT WITH THE BODYWORK SO AS NOT TO DAMAGE IT. FURTHERMORE, DURING THE
BLEEDING OPERATIONS REGARDING THE BRAKE CALLIPERS, MAKE SURE THE BRAKE
FLUID DOES NOT COME INTO CONTACT WITH THE DISC BRAKES AND WITH THE BRAKE
PADS. FAILURE TO COMPLY WITH THIS NORM WILL ENDANGER THE PROPER WORKING AND
EFFICIENCY OF THE BRAKING SYSTEM

If necessary, bleeding can be done using a special vacuum pump

Specific tooling

020329Y

 

MityVac vacuum-operated pump

Locking torques (N*m)

Oil bleed screw

 

8÷12

Brake pipes

Front brake pipes removal

Unscrew the braking splitter screw.

Disconnect the brake pipes removing the two met-

allic straps indicated in the figure.

Remove the brake oil tube fitting from the rigid pipe

inside the front suspension arm and loosen the

hydraulic joint fixing nut of the suspension locking

to release the brake pipes.

Braking system

MP3 400 i.e.

BRAK SYS - 12

Содержание MP3 400 i.e.











































































































































































































































































































































































































Отзывы:

Нет отзывов