PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 105

Страница: 105 / 394

Drive-belt

- Check that the driving belt is not damaged.

- Check the width of the belt.

Characteristic

Minimum width:

27 mm

Standard width:

28.2 mm

Removing the driving pulley

- Using a 27 mm wrench, turn the central pulley nut

to horizontally align the central inside holes and

install the special tool.

Specific tooling

020474Y

Driving pulley lock wrench

- First fit the 2 retainer clamps of the special tool

onto the pulley so that the splines are completely

engaged.

- Then, insert the tool so as to insert the stud bolts

on the ring into the holes obtained onto the tool

itself.

- Tighten the two tool fixing screws, also manually.

- Loosen the central nut.

- Remove the spring washer and the flat washer.

- Remove the fixed driving half-pulley.

- Remove the bushing connection washer.

MP3 400 i.e.

Engine

ENG - 13

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 105 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: