PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 200

Страница: 200 / 394

The control unit is provided with a self-diagnosis

system connected to an indicator light in the in-

strument panel.

Failures are detected and restored by the diag-

nostic tester.

In any case, when the fault is no longer present,

the data storage is automatically cleared after 16

cycles of use (cold start, running at regular engine

temperature, stop).

The diagnostic tester is also required to adjust the

idle mixture.

Specific tooling

020460Y

Scooter diagnosis and tester

The MIU injection-ignition system carries out

checks on the rpm counter and the electric fan for

radiator cooling.

The MIU control unit has a decoder for the anti-

theft immobiliser.

The MIU control unit is connected to a diagnostic

LED on the instrument panel, that also carries out

the deterrent flashing functions.

The MIU control unit power supply is furthermore controlled by the emergency switch; that is to provide

further safety for the scooter.

Precautions

1. Before fixing any part of the injection system, check to see if there are any registered faults. Do not

disconnect the battery before checking for faults.

2. The feeding system is pressurised at 300 kPa (3 BAR). Before disconnecting the fast-release fitting

of the power supply pipe, check that there are no naked flames. Do not smoke. Act with caution to

prevent spraying in the eyes.

3. When fixing electric components, operate with battery connected only when actually required.

4. When functional checks are performed, check that the battery voltage is more than 12V.

Injection

MP3 400 i.e.

INJEC - 4

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 200 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: