PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 295

Страница: 295 / 394

- From the inside loosen the set screw bushing

until the swinging arm is free.

- Remove the swinging arm.

- Check the entire swinging arm assembly.

- Check all the components- Teflon bushings, si-

lent-blocks, roller bushings, spacers.

- Replace the work components that cause exces-

sive clearance on the rear suspension.

Overhaul

- Properly support the swinging arm in the vice.

- Check there is no jamming in the movement of the joint connecting the swinging arm on the engine

side to the swinging arm on the frame side.

- To check the clearance on the frame-side arm, mount the retainer using the pin fixing the swinging

arm to the frame and two adaptor rings of the appropriate tool 020229Y. Alternatively use two washers

with inner diameter for 12-mm pins, min. outer diameter: 30 mm: min. thickness: 4 mm.

- Check there is no sticking in the rotation.

- Check the axial clearance of the swinging arm on

the frame side

Characteristic

Standard clearance

0.40 ÷ 0.60 mm

Allowable limit after use:

1.5 mm

MP3 400 i.e.

Suspensions

SUSP - 49

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 295 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: