PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 156

Страница: 156 / 394

MINIMUM ADMISSIBLE DIAMETER

Specification

Desc./Quantity

Inlet:

4.96 mm

Outlet:

4.945 mm

- Calculate the clearance between valve and valve guide.

- Check the deviation of the valve stem by resting

it on a "

" shaped abutment and measuring the

extent of the deformation with a comparator.

Characteristic

Limit values admitted:

0.1 mm

- Check the concentricity of the valve head by ar-

ranging a comparator at right angle relative to the

valve head and rotate it on a "

" shaped abutment.

Characteristic

Admissible limit:

0.03 mm

Inspecting the valve stem guide clearance

- After measuring the valve guide diameter and the valve stem diameter, check the clearance between

guide and stem.

Engine

MP3 400 i.e.

ENG - 64

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 156 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: