PIAGGIO MP3 400 i.e. Скачать руководство пользователя страница 195

Страница: 195 / 394

Failure to observe the tightening torque may alter

the coupling clearance of the rotors with the pump

body.

Locking torques (N*m)

Screws fixing oil pump to the crankcase

5 - 6

- Insert the countershaft with gearing into the fly-

wheel-side half-crankcase.

- Install the special tool in the position shown in the

figure.

Specific tooling

020479Y

Countershaft lock wrench

- Keep the countershaft in position and insert the

washer with the nut.

- Tighten the nut to the prescribed torque, using

the recommended product.

- Remove the special tool.

Recommended products

Loctite 243

Medium strength threadlock

Loctite 243 medium-strength threadlock

Locking torques (N*m)

Countershaft fixing nut

25 - 29

MP3 400 i.e.

Engine

ENG - 103

Содержание MP3 400 i.e.











































































































































































































































































































































































































Результаты поиска

Содержание MP3 400 i.e.

Отзывы:

PIAGGIO MP3 400 i.e., Руководство по обслуживанию, Страница: 195 / 394

Результаты поиска

Содержание MP3 400 i.e.

Отзывы: