Oracle X7-8 Скачать руководство пользователя страница 275

Страница: 275 / 308

BIOS Advanced Menu Selections

■

“BIOS Advanced Menu Primary Video Selection Options” on page 281

■

“BIOS Advanced Menu Trusted Computing 2.0 Options” on page 281

■

“BIOS Advanced Menu Processor Configuration Options” on page 282

■

“BIOS Advanced Menu Memory Configuration Options” on page 283

■

“BIOS Advanced Menu CPU Power Management Configuration Options” on page 284

■

“BIOS Advanced Menu USB Ports Options” on page 285

■

“BIOS Advanced Menu Error Injection Settings Option” on page 285

■

“BIOS Advanced Menu Disk Freeze Lock Settings Option” on page 285

BIOS Advanced Menu iSCSI Configuration

Options

The following table describes the BIOS Advanced Menu iSCSI configuration options.

Setup Options

Options

Defaults

Description

iSCSI Initiator Name

NA (must be specified)

None

The worldwide unique name of

the iSCSI Initiator. Only IQN

format is accepted.

Add an Attempt

iSCSI Attempt Name

NA (must be specified)

None

The human-readable name that

you assigned to this attempt.

iSCSI Mode

Disabled/Enabled/Enabled for

MPIO

Disabled

Set to Enabled for multipath I/

O (MPIO). MPIO can boost the

performance of an application

by load-balancing traffic across

multiple ports.

Internet Protocol

IP4/IP6/Autoconfigure

IP4

Can be set to IP4, IP6, or

Autoconfigure. The initiator

IP address is assigned by the

system to IP6. In Autoconfigure

mode, the iSCSI driver attempts

to connect to the iSCSI target

using the IPv4 stack. If this fails,

then the iSCSI driver attempt to

connect using the IPv6 stack.

Connection Retry Count

0 to 16

The count range is 0 to 16. If set

to 0, there are no retries.

Connection Establishing

Timeout

1,000

The timeout value in

milliseconds. The minimum

value is 100 milliseconds and

the maximum is 20 seconds.

BIOS Setup Utility Menu Options

275

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды