Oracle X7-8 Скачать руководство пользователя страница 208

Страница: 208 / 308

Replace the ESM Extension Cable

Push it straight down into position..

Attach the ESM connector to the ESM extension cable [2].

Install the SMOD. See

“Install an SMOD” on page 197

Prepare the server for operation. See

“Returning the Server to

Operation” on page 237

Replace the ESM Extension Cable

Prepare the server for cold service.

This is a cold-service component. Power down the system and disconnect the AC power cables

from the server before performing this procedure.
See

“Preparing the Server for Component Replacement” on page 101

Remove the SMOD. See

“Remove an SMOD” on page 195

Rotate the SMOD 180 degrees so the back (connector) side is facing toward you.

208

Oracle Server X7-8 Service Manual • October 2017

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды