Oracle X7-8 Скачать руководство пользователя страница 196

Страница: 196 / 308

Remove an SMOD

This is a cold-service component. Power down the system and disconnect the AC power cables

from the server before performing this procedure.
See

“Preparing the Server for Component Replacement” on page 101

Label and disconnect all cables from the SMOD.

Access this component directly from the back of the server.

Disengage the SMOD from the server midplane.

To unlock the SMOD handles, squeeze together the release latches on the

end of both handles.

To disengage the SMOD from the server midplane, simultaneously, rotate

both handles downward to their fully-open position.

This action disengages the connectors on the SMOD from the connectors on the server

midplane.

Caution -

Physical harm or component damage.

Do not use the SMOD handles to remove the

SMOD from the server.

196

Oracle Server X7-8 Service Manual • October 2017

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды