Oracle X7-8 Скачать руководство пользователя страница 212

Страница: 212 / 308

Replace the SAS Cable

Replace the SAS Cable

This is an internal component that is accessible from the back of the server by removing the

SMOD. Perform this procedure to replace the SAS cables on the SMOD.

Prepare the server for cold service.

This is a cold-service component. Power down the system and disconnect the AC power cables

from the server before performing this procedure.
See

“Preparing the Server for Component Replacement” on page 101

Remove the SMOD. See

“Remove an SMOD” on page 195

Set the SMOD on a flat surface with the front side facing toward you.

Close the SMOD handles.

Rotate the SMOD 180 degrees so the back (connector) side is facing toward you.

Turn the SMOD upside down and locate the HBA.

Note -

The connector (back) side of the SMOD should still be facing you.

The HBA card is located inside the SMOD and is accessible through the an upward-facing

opening on the right side.

Remove the HBA card and disconnect the SAS cables. See

“Remove the HBA

Card” on page 200

Disconnect the SAS cables from the drive backplane.

Carefully route and remove the SAS cables from the SMOD.

10.

Connect the replacement Mini-SAS4I cables to the drive backplane.

11.

Route the replacement SAS cables from the backplane to the SMOD

motherboard.

12.

Ensure that the connectors are routed under the support bracket.

13.

Install the HBA card. See

“Install the HBA Card” on page 203

14.

Install the SMOD. See

“Install an SMOD” on page 197

212

Oracle Server X7-8 Service Manual • October 2017

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды